
One page says treated lumber indoors is against code. The next says it is fine anywhere you like. One of them is about to cost you money.
So can you use pressure treated wood indoors? Yes, and in a few spots the residential code requires treated or naturally durable wood: sills and sleepers on a ground contact slab, framing close to exposed ground in a crawlspace, wood against below grade masonry.
Everywhere else it is legal and usually a waste. The table below sorts your spot into one of four verdicts.
Table of Contents
- Key Takeaways
- Where Treated Wood Belongs Indoors And Where It Does Not
- Where The Building Code Requires Treated Wood Inside Your House
- What Is Actually In Treated Wood Now, And How To Handle It
- Why Treated Lumber Is A Poor Choice For Ordinary Interior Framing
- Borate Treated Lumber: The Treated Wood Made For Indoors
- Framing, Floor Joists, Garages, Furniture And Sealing
- Bottom Line
- FAQs
Key Takeaways
- Code requires treated or naturally durable wood in interior spots: sills on a ground contact slab, crawlspace framing near exposed ground, wood against below grade masonry.
- Everywhere else in a dry conditioned space it is legal and usually pointless.
- The arsenic formula left residential shelves at the end of 2003, and today’s boards are copper based or borate.
- Treated wood needs hot dip galvanized, stainless, silicon bronze or copper fasteners, with one exception for dry borate lumber.
- Never for countertops, cutting boards or anything food touches, and never burn it.
Where Treated Wood Belongs Indoors And Where It Does Not
Find your row in the table below and the rest of this page is optional.
Every verdict comes down to two questions. Can that piece of wood pick up moisture from concrete or from the ground, and is anything going to eat off it.
Concrete and soil pass water into whatever touches them, and damp wood is exactly what rot fungus and termites are looking for. Framing in the middle of a conditioned wall is neither wet nor exposed.
| Location Or Use | Treated Wood? | Why |
|---|---|---|
| Sill or bottom plate on a slab or foundation wall | Required | Code lists sills and sleepers on a ground contact slab, and concrete wicks moisture straight into the plate |
| Crawlspace joists and girders near exposed ground | Required | Clearance triggers it: 18 inches for joists, 12 inches for girders, 8 inches for columns |
| Furring or framing on below grade block or concrete walls | Required | Unless an approved vapor retarder sits between the wall and the framing |
| Wood columns sitting on a basement floor slab | Required | Unless the post stands on a concrete pier or metal pedestal above the slab with a moisture barrier |
| Basement or garage wall framing above the bottom plate | Pointless | It stays dry, so plain lumber does the same job for less |
| Interior partition framing | Pointless | Same, unless you are buying borate lumber on purpose for termites |
| Floor joists inside a conditioned space | Pointless | Dry framing, and wet treated stock keeps moving after you nail it up |
| Garage shelving and workbenches | Fine | Legal and common, just use corrosion resistant fasteners and keep the dust down |
| Furniture and shelving in the house | Pointless | Heavy, wet and splintery, and it costs more than the right wood for the job |
| Countertops, cutting boards, anything food touches | Never | The preservative must never become part of food |
Where The Table Surprises People
Start with the bottom plate on the concrete. It is required, and the studs standing on top of it are not, which is why most basement walls need exactly one treated board.
The Fine row gets worried about the most and deserves it the least. A treated workbench in a garage is a normal thing to build, and the cautions are about rusting fasteners and sanding dust, not about the air in the room.
The Never row has nothing to do with the house. It is about food, because the preservative can never become part of what you eat.
Kids’ furniture and toys sit just off the bottom of that table. Nothing bans treated wood there today, but with constant hand to mouth contact and nothing to gain, plain lumber is the better build.
Four of those rows come straight out of the building code.
Where The Building Code Requires Treated Wood Inside Your House
Plenty of builders think treated lumber inside the house breaks code. It does the reverse.
Section R317 in most editions covers protection against decay, and it bans nothing indoors. It lists the locations where ordinary lumber is not allowed, and several sit inside your walls.
The Interior Locations On The List
The interior entries sit at the bottom of the house:
- Crawlspace joists or the bottom of a wood floor closer than 18 inches to exposed ground, girders closer than 12 inches, columns closer than 8 inches
- Framing and columns resting on exterior concrete or masonry foundation walls and less than 8 inches from exposed ground
- Sills and sleepers on a slab in direct contact with the ground, unless an impervious moisture barrier separates them
- Girder ends entering exterior masonry or concrete walls with less than half an inch of clearance around them
- Furring or framing fixed directly to below grade masonry or concrete walls, unless an approved vapor retarder sits between
- Columns sitting on a basement floor slab, unless they stand on a concrete pier or metal pedestal with a moisture barrier
The trigger is contact and clearance to ground, concrete or masonry, not which room you stand in.

Naturally Durable Wood Counts Too
Treated is not the only way to pass. The code allows naturally durable wood, or wood treated to the American Wood Protection Association standard AWPA U1, so cedar or redwood heartwood qualifies too.
One rule catches every DIYer. Cut ends, notches and drilled holes get treated again in the field, with the brush on preservative sold beside the lumber.
What Is Actually In Treated Wood Now, And How To Handle It

The thing most people picture when they hear treated wood left homeowner shelves more than twenty years ago.
The 2003 Change And What Replaced It
Effective December 31, 2003, chromated arsenical manufacturers voluntarily canceled virtually all residential uses of chromated copper arsenate, the CCA formula. Wood treated with it is no longer used in most residential settings, decks and children’s playsets included.
The EPA’s overview of wood preservative chemicals now classifies chromated arsenicals as restricted use products for certified applicators. What sells to homeowners today is copper based or borate.
Alkaline copper quaternary is the most widely used residential preservative, copper azole sits beside it, and borate is the one the EPA lists for interior construction, sill plates included.
An older deck built from the CCA formula does not have to come down, per the EPA, and a penetrating stain applied regularly may reduce leaching.
The Real Dangers Of Treated Wood Indoors, And What Handles Them
The National Pesticide Information Center fact sheet on treated wood is the shortest useful list. Wear a dust mask when cutting or sanding, add goggles and gloves, and work outdoors or somewhere ventilated, because dusts build up in closed rooms.
Wash your hands before eating or drinking, and launder sawdust covered clothes separately. The same sheet goes as far as suggesting a tablecloth on a treated picnic table to cut skin and food contact.
Keep ash and compost from treated wood out of an edible garden, and never burn it, because burning treated wood changes what comes out of the smoke.
Notice what is missing from both lists. Neither warns about fumes in a closed house. Every published precaution is about dust, skin, hands and fire.
Why Treated Lumber Is A Poor Choice For Ordinary Interior Framing
Nail up wet treated studs in a heated basement and the wall you drywalled in March is not the wall you have in August.
It Comes Wet And It Moves As It Dries
The preservative rides into the board in water, so treated lumber leaves the plant soaked and keeps giving that water back inside a heated house.
Installers report treated stock arriving far wetter than kiln dried framing, then twisting and shrinking well past what a plain stud does.
Fresh treated stock can take weeks or months to dry enough to hold a finish.
One product exists for exactly that problem: kiln dried after treatment, sold as KDAT, goes into the oven after the chemical goes in and comes back out at the wood’s original moisture content. It costs more and usually has to be ordered.
The Code Makes You Buy Different Fasteners
The code’s fastener rule for treated wood calls for hot dipped zinc coated galvanized steel, stainless steel, silicon bronze or copper, and stainless steel staples.
Every screw, hanger, strap and anchor in that wall changes, and none of them get cheaper.
One narrow exception exists. Plain carbon steel fasteners are allowed in borate treated wood in an interior, dry environment.
You Pay More For Less
Treated stock costs more than the same size in plain framing lumber, it is heavier up the stairs, and it splinters. On a dry interior wall that extra money buys nothing you can point at.
Above the bottom plate, ordinary framing lumber does the job better and cheaper.
Borate Treated Lumber: The Treated Wood Made For Indoors

In heavy termite country, parts of the Gulf Coast and Hawaii among them, builders sometimes frame a whole house in treated lumber, studs, joists and rafters. It is not the green board from the yard.
Borate treatments are built for interior, above ground, dry framing: sill plates, studs, joists and blocking. They defend against termites as well as decay fungus, and higher borate retentions are specified where the Formosan termite is present.
The limit is water. Borate protects the board only while the board stays dry, which is why it sells for interior use and never for ground contact.
That plain carbon steel exception was written for this wood, so framing with borate lumber skips the galvanized hardware bill.
The AWPA use categories are how you confirm it at the yard. The two interior grades are UC1, above ground interior construction dry, and UC2, above ground interior construction damp, the grade that covers sill plates; deck lumber carries the exterior and ground contact grades instead.
Those categories are printed on the stamped tag on the end of the board, next to the preservative name and whether the board is meant for indoors or outdoors and for ground contact or above ground. Read it before the board goes in the wall.
Framing, Floor Joists, Garages, Furniture And Sealing
Most of the arguing happens over five spots, and each one lands differently.
Interior Walls And Framing
Treated only where the code list puts it, which in most basements is the bottom plate and nothing above it.
The recurring mistake is treating the whole wall when one board touches masonry. Borate lumber for a full wall in termite country is a deliberate upgrade.
Floor Joists
Required inside the crawlspace clearances to exposed ground, pointless in a dry conditioned floor.
One crew that reused old treated deck boards as interior floor sheathing found the boards had stained the sheathing underneath as they dried.
Garages And Workbenches
Fine, and common. The plate on the garage slab follows the same code rule as the house. Use corrosion resistant fasteners, keep bare steel tools off the top, and check what the wall behind your shelves can hold before loading it.
Furniture, Countertops And Anything Food Touches
Allowed for ordinary furniture, never for anything food touches. A cutting board or a countertop is the absolute line, because the preservative cannot become part of food.
It also makes poor furniture: wet, heavy and rough, at a price above the wood you actually want.
Sealing Or Painting It For Indoor Use
Sealing changes nothing about what the board is rated for, and it never makes treated wood food safe. Order matters more: let the board dry out before any finish goes on, because a coating will not hold on wet treated lumber.
Bottom Line
Yes, and in a short list of spots the code requires it. That list is sills on a ground contact slab, framing close to exposed ground in a crawlspace, and wood against below grade masonry.
Everywhere else in a dry house it is legal and a waste. It arrives wet, it keeps moving after you nail it up, and it drags corrosion resistant fasteners with it for no gain.
If you want treated wood indoors on purpose, the interior grade is borate, and the end tag confirms you got it. Ask for it by name at the counter.
One treated bottom plate, plain lumber above it, and a can of field cut preservative for the saw cuts covers the average basement wall. Two lines never move: nothing food touches, and never burn it.
FAQs
Can You Use Treated Lumber For Interior Walls?
Yes, and the code requires it for the bottom plate sitting on a concrete slab or foundation wall. Above that plate, in a dry conditioned space, plain framing lumber is the normal choice, and it costs less and stays straighter. Borate lumber is the exception worth buying on purpose.
Is Pressure Treated Wood Safe Indoors?
Yes for anything food does not touch. The arsenic formula left residential shelves at the end of 2003, and today’s boards are copper based or borate. The published precautions cover sawdust, hand washing and burning, not fumes in a closed room.
Can You Use Pressure Treated Wood For Framing?
Yes, and in the code listed spots you have to. For ordinary dry framing it is a poor trade: wet stock that shrinks and twists, corrosion resistant fasteners at every connection, and a higher price for nothing you can see later.
Can You Use Treated Lumber For Floor Joists?
Yes, and it is required for crawlspace joists and girders inside the code clearances to exposed ground. In a dry conditioned floor it is pointless, and reused treated deck boards can stain the sheathing under them as they dry out.
Can You Seal Pressure Treated Wood For Indoor Use?
You can, but sealing changes nothing about what the wood is rated for and it never makes the board food safe. Sealing is a finish choice. Let the board dry fully first, because a finish will not hold on wet treated lumber.





